Outliers > Modified Thompson Tau Test

## What is the modified Thompson Tau Test?

The modified Thompson Tau test is a way to find outliers in a data set. The data set must be a single variable (e.g. x_{1}, x_{2},…x_{n}). One potential outlier is tested at a time using a version of the t-test. Roughly speaking, the Tau test eliminates outliers more than two standard deviations away from the mean.

Like most tests for outliers, there is the possibility that you could eliminate good data (especially if there is a cluster of outliers), so you should interpret the results of the test with caution.

## Running the Test

In order to run the test, you first have to identify a *possible *outlier.

Example question: Are any of the following points outliers? : 489, 490, 490, 491, 494, 499, 499, 500, 501, and 505.

**Part 1: Identify a potential outlier**

Step 1: Find the sample mean. The mean for this set of data is 495.8.

Step 2: Subtract the mean from the highest and lowest data point to find the absolute value of the differences. As a formula, that’s:

δ_{i} = |x_{i} – x̄|.

So:

- |489 – 495.8.| = 6.8
- |505 – 495.8.| = 9.2

The point with the highest absolute difference (δ) is a suspected outlier. This is the one you’ll test. For this example, that’s **9.2.**

**Part 2: Test the data point**

Step 1: Look up the sample size (n) in the Tau table below to get the Tau value (for the formula behind the table calculations see

*Tau Formula*below):

For a sample size of 10, Tau is

**1.7984.**

Step 2: Calculate the standard deviation (s) for the sample. For this set of data, **s = 5.67.**

Step 3: Multiply Tau (Step 1) by s (Step 2):

Tau * s = 1.7984 * 5.67 = 10.2

Step 4: Compare the absolute difference (δ) for the suspected outlier (from Part 1) with Tau * s (Step 3).

If δ > Tau * s, the point is an outlier.

9.2 is not greater than 10.2, so is therefore **not **an outlier.

## Repeating the Steps

In the above example, the point with the largest absolute difference was not an outlier. If the point *is *an outlier, repeat the steps above for the point with the next largest deviation. However, when you repeat the calculations, you must *remove the outlier you identified before recalculating the mean and finding the new Tau*.

## Tau Table

n | Tau | n | Tau | n | Tau |
---|---|---|---|---|---|

3 | 1.1511 | 21 | 1.8891 | 40 | 1.9240 |

4 | 1.4250 | 22 | 1.8926 | 42 | 1.9257 |

5 | 1.5712 | 23 | 1.8957 | 44 | 1.9273 |

6 | 1.6563 | 24 | 1.8985 | 46 | 1.9288 |

7 | 1.7110 | 25 | 1.9011 | 48 | 1.9301 |

8 | 1.7491 | 26 | 1.9035 | 50 | 1.9314 |

9 | 1.7770 | 27 | 1.9057 | 55 | 1.9340 |

10 | 1.7984 | 28 | 1.9078 | 60 | 1.9362 |

11 | 1.8153 | 29 | 1.9096 | 65 | 1.9381 |

12 | 1.8290 | 30 | 1.9114 | 70 | 1.9397 |

13 | 1.8403 | 31 | 1.9130 | 80 | 1.9423 |

14 | 1.8498 | 32 | 1.9146 | 90 | 1.9443 |

15 | 1.8579 | 33 | 1.9160 | 100 | 1.9459 |

16 | 1.8649 | 34 | 1.9174 | 200 | 1.9530 |

17 | 1.8710 | 35 | 1.9186 | 500 | 1.9572 |

18 | 1.8764 | 36 | 1.9198 | 1000 | 1.9586 |

19 | 1.8811 | 37 | 1.9209 | 5000 | 1.9597 |

20 | 1.8853 | 38 | 1.9220 | → ∞ | 1.9600 |

## Tau Formula

If you’re using the table, you don’t really need the formula (unless you’re calculating some specific sample size not listed). Tau is calculated from T critical values of student’s T-distribution, which identify a rejection region. The formula is:

**Where**:

- n = sample size
- t
_{α/2}= student’s T critical value (based on an alpha level of 5%) with two degrees of freedom

**Need help with a homework or test question? **With Chegg Study, you can get step-by-step solutions to your questions from an expert in the field. Your first 30 minutes with a Chegg tutor is free!

*Statistical concepts explained visually* - Includes many concepts such as sample size, hypothesis tests, or logistic regression, explained by Stephanie Glen, founder of StatisticsHowTo.

**Comments? Need to post a correction?** Please post a comment on our *Facebook page*.